New equipment in the house requires studying the operating instructions. Boring activity. Valuable information is always hidden behind a pile of technical terms and is often difficult to digest. But the correct and correct operation of the devices depends on this. To connect the boiler, you can call a specialist, but you can save money and do all the work yourself. We invite you to familiarize yourself with the standard instructions for connecting the boiler. Everything is presented here, clearly and concisely.
The boiler is installed. Whether the installation work was carried out by specialists or the owner does not matter. In any case, you need to check the operation of the system. To do this, following the given tips, you need start the heater for the first time.
- We start by checking that the systems are connected correctly, which are responsible for heating the water. Fidelity, reliability of connection of phase and neutral wires, presence of grounding. The functionality of the circuit breaker should also be checked. To do this, use a device - a tester or a special electrician's screwdriver.
- Next comes the search for leaks in the system.. It would be useful to control the connection of underwater pipes. Presence and diagnostics of check valve operation.
- Running water into the boiler. Attention, correct sequence actions during the first and subsequent system starts will be described in the next section.
- Repeated searching for water leaks in pipe installation areas b.
- Diagnostics of heater operation. Turn on the device by pressing the power button.
- Fixation of initial indicators temperature sensor.
- Recheck after 15 minutes. An increase in indicators indicates the correct connection of the heating elements.
Sequencing
It is immediately worth mentioning that the following The startup sequence is correct for both instantaneous and storage heaters. A couple of nuances - in the case of the first type, you do not have to wait for the tank to be filled with water and close the tap at the 2nd point.
- You should start by turning off the supply hot water , which comes from the city supply system. If you skip this step, the water heated by the boiler will go into the common riser, despite the check valve.
- Open the tap with hot water . We wait until the remaining liquid drains from the pipes. Close the tap.
- Two pipes go to the bottom of the boiler. One, marked with a blue ring, is underwater, the other, with a red marker, serves to supply hot water to the pipes.
- Open the valve on the underwater pipe. Water begins to flow into the device’s storage tank.
- Next, unscrew the second valve on the boiler. Allowing the water to escape into the pipes.
- Open hot water on the mixer. We wait until the air leaves the system and a steady stream of water flows. We turn off the water.
- Connect the heater to the electrical network and set the desired temperature.
In a house where there is no hot water supply, the first step must be skipped. Subsequent switching on of the heater will follow the same pattern. The only difference is in point 6. Then not air, but stagnant water will begin to come out of the heater tank.
Heating mode selection
Set the heating mode. The main thing in this matter is to set the water temperature that is comfortable for the user.. However, here are a few tips, the implementation of which will significantly extend the service life of the device. This will save you money on future repairs.
- Set the temperature to 30–40 degrees as little as possible. Under such conditions, bacteria will quickly develop inside the storage tank. This will result in an unpleasant musty odor. The walls will become covered with fungus, which is difficult to remove.
- Optimal operating mode, 55–60 degrees. In this temperature range, less scale will form on the heating element. The risk of mold will be reduced. It is comfortable for human skin.
- Once a week the boiler must be set to 90 degrees. Wait a couple of hours and return to the previous mode. This is done to completely destroy bacteria in the storage tank.
- Some devices have an economical operating mode. In this case, the heater does not consume less electricity. The settings will be set as in step 2 and we're talking about about reducing the risk of breakdown.
- In the case of a flow-type heater, the temperature is also adjusted by water pressure.
Rules for using the device
You can use the storage type device immediately after the first start. To do this, you need to turn it on and select the operating mode. Throughout operation you will have to follow some rules. They will help increase the service life of the boiler.
- Before turning on, check the presence of water in the tank. This will prevent the heating elements from failing.
- It is recommended to install a filter on the pipe supplying water to the boiler. It will protect against dirt and reduce water hardness.
- During the year, descale the drive at least once.
- Periodically monitor the performance of the protective anode, change if necessary.
Flow type devices require compliance with several other rules.
- Check the water pressure before turning on the power. A weak stream will not allow the device to function normally.
- If the temperature is uncomfortable, adjust it using the buttons on the body or by rotating the mixer tap.
- If the heater is installed in a bathroom, organize splash protection.
- Hot water is no longer needed - be sure to turn off the device.
Equipment reliability depends not only on product quality. Also important: correct installation, switching on and use of equipment. Compliance with the recommendations given in the article will significantly increase the time uninterrupted operation boiler
The Polaris trademark has existed on the technical market since 1992. Today the company occupies a niche of international manufacturers household appliances, since it has production units in four countries. The range of branded products includes a variety of household equipment, including the Polaris water heater.
Several historical factors
The name of the Polaris brand comes from the name of the North Star. The concern was formed in 1992, in the month of October. It was then that a small group of graduates of the Moscow Aviation Institute decided to open private company for the production of televisions. The first models equipped with remote controls were produced on Philips lines. But in 2003, the first own production factory, which is located in the Kaliningrad region, went into operation.
The company regularly found new manufacturers of household equipment to establish partnerships. In this way, it could significantly expand its product range. More than 700 types of equipment are produced under this brand, for example:
- Polaris boilers;
- electric grills;
- meat grinders;
- vacuum cleaners;
- air conditioners;
- radiators;
- laser measuring devices;
- dishes, etc.
The department of engineers and designers are working to create new series of products taking into account the needs of the modern consumer and innovative technologies.
Rating of the best Polaris water heater models
From the entire range of offers, owners of Polaris water heaters have identified a rating of the best variations that deserve the attention of consumers.
Polaris Aqua IMF 50v
The Polaris storage electric water heater has a bottom connection and is installed in a vertical position. The model has a pressure supply system, so it requires connection to several water intake points.
Polaris Aqua IMF 50v
The tank holds water with a volume of 50 liters, Polaris is capable of heating the contents to a temperature of 75°C. There is protection against turning on without water and against overheating. The inside of the tank is covered with stainless steel, and the power of the heating element is 2.5 kW. The cost of the Aqua IMF storage water heater is 14,000 rubles.
VIDEO: Review of Polaris Aqua IMF 50v operation
Polaris ultra IMF 80 V
The Polaris 80 liter storage heater has a maximum power of 2.5 kW, but has three heating modes. In the production of the Polaris electric storage water heater tank, a special tungsten coating of the joints was used to increase the degree of reliability and service life.
Polaris ultra IMF 80 V
The design features a copper heating element, as well as three levels of protection against leaks and overheating. The dimensions of the Polaris ultra IMF 80 water heater are 67x46.5x34 cm, the model weighs 10 kg. The price of the device is 17,000 rubles.
VIDEO: Overview of operation and installation rules of Polaris ultra IMF 80 V
Polaris mercury OD 5.3 (flow-through)
The Polaris Mercury electric instantaneous water heater will solve the problem of organizing an autonomous water supply in any home. The power of the model is 5.3 kW. The package includes an instruction manual, shower head, and hose.
Polaris Mercury OD 5.3
Installation of a flow-type water heater is carried out using the vertical method, and water pipes are connected to the equipment from below. The completely empty device weighs 3.1 kg, its productivity reaches 4 l/min, and the maximum temperature is 55°C. On the control panel you can select 1 of four operating modes. The cost of an instantaneous electric water heater is 5,000 rubles.
VIDEO: Review of Polaris Mercury OD 5.3
Polaris pf 50 VR (cumulative)
The Polaris water heater has a power of 2 kW. Water is supplied to the intake points under pressure up to 8 atm, thanks to which the device can be connected to several water outlets.
Polaris pf 50 VR
There is a thermometer and temperature limiter, as well as a mechanical control system. Polaris 50 liters is installed vertically and fixed to the wall surface with brackets. The model uses a copper heating element, which is not subject to corrosion, as a heater. Price - 7900 rubles.
VIDEO: Review of Polaris pf 50 VR operation
Polaris ultra 3.5 (flow-through)
This is a wall-mounted compact heater with a power of 3.5 kW. The design includes a thermometer, start indicator, heating indicator, temperature limiter and safety valve. The electric instantaneous water heater has a round shape and dimensions of 25.7x38.7x8.4 cm.
Polaris ultra 3.5
On the front panel there is an information display that informs the user about the specified operating mode. The device weighs 3.4 kg. Cost - 3900 rubles.
VIDEO: Review of Polaris ultra 3.5 operation
Polaris Gamma IMF 100 V
A 100 liter electric storage device is capable of heating water up to 75°C. There is a digital display and an electronic control system. The package includes a stainless steel tank; this model has an anti-corrosion anode and a start indicator.
Polaris gamma IMF 100 V
A device with dimensions 55x88.5x37 cm weighs 20.4 kg. The Gamma model has overheating protection, a safety valve, and an accelerated water heating function. The device is installed on the wall in a vertical position with the lower supply of the water supply system. Price - 14,500 rubles.
Polaris Vega IMF 50H
A storage water heater with a volume of 50 liters and a power of 2.5 kW assumes operation at several points. It contains a mechanical control system, start and heating indication, accelerated warm-up function, thermometer, information screen, temperature limiter.
The safety system includes overheat protection and one anode. The storage tank consists of stainless material. The device is installed in a horizontal position on the wall, and the pipeline is connected to it from the bottom. The dimensions of the model are 80.9x45x24.8 cm. The cost of the Polaris Vega IMF 50H storage water heater does not exceed 17,500 rubles.
Problems and malfunctions of Polaris water heaters
Malfunctions extremely rarely occur on their own, unless we are talking about a manufacturing defect. Technically sound equipment can be damaged in several cases:
- voltage drop in the network;
- ignoring the need for regular maintenance;
- water heater installation errors;
- the formation of plaque on the heater elements, the appearance of pockets of corrosion;
- untimely replacement of non-functioning parts.
VIDEO: Repair of water heating tank FD -100V Polaris
Large-sized equipment and compact devices for heating water are actively involved in creating comfortable conditions. Few city dwellers know how to use a water heater, because... their apartments are connected to a centralized hot water supply. However, if you have to live in a Khrushchev building or in a dacha, information about the operation of complex units will be extremely useful, don’t you agree?
With us you will receive informed answers to all questions that arise when using the devices. In the article we have proposed, the topic of water heaters is discussed in detail, their types and design features are indicated.
The specifics of installation and rules for proper operation are described in detail. Technological subtleties and nuances of care are indicated. To make it easier to understand, the information is supplemented with photos, diagrams and video tutorials.
Flow-through models heat the water coming from the water pipe immediately after opening the tap. Visually, such models are significantly smaller in size and are mounted next to the crane.
A type of instantaneous water heaters is a special tap. It does not require a lot of electricity and can be a real godsend for the garden
Depending on the fuel consumed, storage and flow devices most often include:
The first ones have a higher initial cost, but pay for themselves after 2 years. The latter are initially 2-3 times cheaper, but due to the high cost of electricity, already in the third year of use they are more expensive for their owner.
This dependence is valid with constant use.
Flow-through heater models can be equipped with a kitchen spout and shower head. They are mounted next to the faucet to avoid large heat losses
If we are talking about seasonal stays at the dacha and the use of small volumes of warm water, then the electric option will come in handy for a potential buyer.
After all, electricity is supplied to many summer cottages, and as for gas, the situation with its availability may be worse. And if you rarely use the device, it will consume very little electricity.
Regardless of the type of water heating device purchased, you must handle it carefully and use it for its intended purpose. Moreover, the operating features of all similar models are similar, but there are also fundamental differences.
To avoid harming an expensive device through ignorance, it is better to read the instructions on how to properly use a specific water heater model.
Subtleties of operating flow-through units
Differences in appearance and the design of flow-through and storage models cause some nuances during operation.
Therefore, before starting to use the unit, it is important to carefully study the recommendations specified by the manufacturer.
A flow-through tap water heater can be used not only in the country, but also in a city apartment. It is easy to install and connect yourself
The most common requirements that must be met before operating storage and flow-through models are as follows:
- installation of a coarse filter;
- strictly horizontal installation;
- grounding for electrical appliances.
The horizontal position is checked by the building level. Strict adherence to this rule will help prevent the formation of air locks.
It is also important to consider that there are models that can only be installed horizontally or only vertically. If you neglect this rule, the equipment will, at best, not work, and at worst, it will simply burn out.
Small models of vertical flow electric heaters can easily fit into the kitchen design. And a 10-liter device won’t take up much space.
There are also models that provide a user-selectable mounting option - horizontal or vertical. The design features of the device are designed for any position and this will not affect further operation.
Instantaneous water heaters are produced by many domestic companies. Also on the market you can find a large number of offers from European and Chinese companies.
Storage water heaters come in both horizontal and vertical types. Moreover, this rule applies not only to small-volume boilers
Many manufacturers offer storage models that require gas or electricity to operate.
The first option, when constantly used by a family of 5 people for 4-5 years, will cost 3-4 times less than the electric option in terms of the total cost of purchasing, connecting and paying for gas. Although, the cost of the unit itself in stores is about 2.5-3 times cheaper than a gas appliance.
You can only operate a boiler that is correctly installed and connected to the power supply network. The specialist who carried out all the work is obliged to put a note about this in the warranty card and test the quality of installation of the equipment.
Without his signature and seal of the organization, in the event of a breakdown, the guarantee cannot be used.
If everything is installed by a responsible technician, then the owner can begin to operate the water heater. First, you need to inspect the equipment from all sides and make sure that everything is intact, there is no visible damage, the wire and plug have not melted anywhere and nothing is leaking.
If the visual inspection was successful, you need to fill the boiler or make sure that it is full. To do this, open the water supply valve to the unit and unscrew the hot water tap. As soon as water starts flowing from the tap, the storage heater is full.
Now you can plug the device into the socket and press the “on”/“on” button on the case. Control and adjustment are carried out using the corresponding buttons.
Depending on the equipment model, control and adjustment of the desired temperature can be carried out mechanically or by entering appropriate commands on the monitor.
The technical perfection of the device directly affects its cost. In everyday life, models with the most necessary functions and simple controls are most often purchased. The simpler it is, the fewer breakdowns in the future.
You may find the information about self-help, discussed in our other article, useful.
In practice, electronically controlled water heaters do not tolerate installation in a bathroom. It is advisable to avoid installation in a room with high humidity levels
When operating, it is important to follow all the rules described by the manufacturer in the instructions for a specific device. Also, never turn on a broken heater.
If the external condition causes concern or traces of melting are visible on the wiring or plug and socket, you should definitely contact a specialist.
If the storage unit is the main source of hot water in the house/apartment, then, in order to save money, you should not unplug it.
Thanks to the installed thermostat, the device will turn on to heat water only when necessary. As soon as the water reaches the desired temperature, it will automatically turn off.
This work allows you to use electricity or gas as economically as possible if it is a gas water heater. It is advisable to turn off the equipment only in case of a long absence of the owner and all residents of the house, cottage or apartment.
Image gallery
Water heaters" href="/text/category/vodonagrevateli/" rel="bookmark">water heaters . We are confident that you will be satisfied with the purchase of a product of the “POLARIS” brand.
Before using the appliance, please read these instructions carefully, as they contain important information regarding your safety, as well as recommendations for correct use device and its care.
Save these instructions along with your warranty card and sales receipt.
Purpose and scope· Electric storage water heater is designed to provide hot water supply to apartments, cottages, bathhouses and other domestic premises.
Safety requirements· The manufacturer warns that improper compliance with the requirements of this instruction, as well as unauthorized “improvement” of the device design, can lead to consequences dangerous to the health and life of the consumer.
· The electrical connection must be made in accordance with the electrical diagram below.
· The supplied safety valve must not be plugged or replaced.
· Installation and connection must be carried out by specialists with the necessary qualifications.
· Attention! Do not install horizontally vertical water heaters, and vertically horizontal .
· Hoses and connections connected to the water heater must withstand operating pressure up to 6 bar and temperature up to + 80°C.
· The device must be grounded.
· If the device will not be used during the winter (for example, at the dacha), then in order to avoid destruction of the product due to expansion of water when freezing in the water heater, all water should be drained from the device.
3. Technical description
1. Temperature adjustment is carried out within the range of 35°C - 75°C with a digital display of the temperature of the heated water.
2. The device can be used in a wide range of water pressures and volumes; capable of supplying multiple consumers simultaneously.
3. The inner walls are made of high quality stainless steel.
4. The device has good thermal insulation properties, which allows it to maintain temperature for a long time.
Protection against changes in water pressure (if the water pressure exceeds 6 bar, the pressure is automatically released). Overheat protection. Thermometer, thermostat and bipolar thermostat built into the water heater.
During operation, the water heater tank is constantly under pressure from the cold water main. The water is heated by a heating element located at the bottom of the tank. When hot water is consumed, cold water entering the bottom of the tank displaces the heated water through the hot water intake pipe at the top of the tank into the hot water distribution line.
When the set temperature is reached, the electronic thermostat automatically turns off the heating element. An electronic thermometer shows the temperature of the water in the tank. When the temperature drops, the water heater turns on automatically.
To ensure proper installation and proper use of the product, you are provided with the following information.
1. Design and names of parts
2. Main technical characteristics and electrical diagram
3.1 Installation requirements
3.2 Mounting method
3.3 Preparation and connection
3.3.1 Connection to the water supply system
3.3.2 Electrical connection
4.Usage
5. Points that require attention
6. Service
7. Scope of delivery
8. The most common malfunctions and their elimination
9. Service life
10. Warranty
1 . Design and names of main parts
Left cover front panel insert drain hole hot water outlet cold water inlet electric cable right cover display magnesium anode brackets rear panel
| ||||
Stream 5.0 – 30 H | ||||
Stream 5.0 – 50 H | ||||
Stream 5.0 – 80 H |
Size2. Basicspecifications
and electrical diagramDIV_ADBLOCK5">
| Nominal voltage | Nominal | Rated power | Maximum pressure |
||
Stream 5.0 – 30 H | ||||||
Stream 5.0 – 50 H | ||||||
Stream 5.0 – 80 H |
Options3. Installation
Installation of the device is carried out by the buyer at his own expense.
The manufacturer is not responsible for problems caused by improper installation and neglect of the recommendations of this manual, namely:
a) The electrical connection must be made in accordance with the rules in section “3.3.2 Electrical connection”.
b) The safety valve included in the delivery must not be plugged or replaced.
To reduce heat loss along the length of the pipes, the device should be installed as close as possible to the place of hot water consumption. To facilitate maintenance of the device, leave space for free access to electrical parts (approximately 0.5 m). In addition, it is recommended to install the water heater at a distance of 20-25 cm from the ceiling and adjacent walls.
3.1. Installation Requirements
§ Despite the fact that the device has good protection against current leakage, we recommend installing a protective regulator on the power circuit (RCD) and ensuring reliable grounding.
Electricity sources rated at 220 volts and 50 Hz are used.
§ The rated current values for the protective regulator on the power supply circuit must be no less than the current values for the water heater.
§ Keep the safety regulator on the power circuit clean to prevent current leakage.
§ A safety valve must be installed on the cold water receiver filler hole.
§ The drain tube installed on the pressure relief valve must face down and be free.
§ The wall to which the heater is attached must be strong. If the wall cannot support the double weight of the heater tank filled with water, the user must install a support under the bottom of the heater.
§ A water drain must be provided at the place where the heater is mounted.
3.2 Mounting method
1. Select a suitable location to install the water heater. In accordance with the markings presented in Figure 1, using a drill with a diameter of 12 mm, drill four holes in the main wall on the same line.
2. Insert the dowels into the holes and secure the bracket to the wall using self-tapping screws. (When installing the water heater in a wall recess, use the dimensions shown in the diagram on page 5).
3. Hang the water heater, securing it to the brackets. Make sure the screws are tight and the water heater is securely fastened.
4. The heater must be mounted in dry, dark places; in order to avoid heat loss, the heater must be mounted in a place located as close as possible to the water supply.
3.3 Preparation and connection
3.3.1 Connection to the water supply system :
1. Hoses and connections connected to the water heater must withstand operating pressure up to 6 bar and temperature up to +80°C.
2. With a standard connection, the water heater operates under pressure determined by the pressure in the line.
The water heater inlet pipe is connected to the water supply system through the safety valve included in the delivery set.
 |
To avoid damage, do not use too much force when screwing in the safety valve.
The safety valve has two functions:
Allows water to flow in one direction only
(is a check valve).
At pressures above 6 bar, the water bleeds out through a hole on the side.
(calibrated at 6 bar).
The appearance of water droplets from the safety valve opening during water heating is a natural process and is associated with the expansion of water in the tank when heated. We recommend connecting the valve hole with a flexible outlet tube to the drain system.
Under no circumstances should the valve opening be closed!
If the water pressure in the main exceeds 5 bar (atmospheres), a pressure reducer should be installed after the water meter.
Connection diagram for several taps
Connection diagram for one pin
3.3.2 Electrical connection.
1. Reliable grounding must be provided.
2. Use energy sources with a voltage of 220 volts and 50 Hz
3. To connect the water heater to the electrical network, use a two-pole switch (preferably an automatic switch) with a distance between contacts of at least 3 mm.
4. A residual current device (RCD) should be installed in the power supply circuit. Seek advice from a qualified professional.
Make sure that the mains voltage corresponds to the value indicated on the marking plate (nameplate).
UsageImmediately before turning on, fill the water heater with water. To fill the water heater with water, it is necessary to open the common valve of the water supply network and the hot water use valve. The appliance is completely filled with water when it flows out of the hot water tap at full capacity.
Attention! Only when the device is completely filled with water can the heating element be connected to the electrical network.
After filling the water heater, close the hot water tap, inspect the unit and make sure it is not leaking. Plug in the water heater.
1. Turn on the temperature controller control buttons:
temperature adjustment" (left) and the "on - off" button (right)
The "temperature adjustment" button is used to control and set the temperature.
The "on - off" button is used to start and stop the heater.
b) Digital display (two-digit, eight-position): used to display temperature adjustment and its actual values (00 - 99), issue warning signals (E2-E4)
c) Standby mode: the heater is on, but no heating is produced. The gauge displays the current water temperature reading.
d) Switching on mode: switching on is done by pressing the “on” button, the display shows the value of the previously set temperature (if the temperature is not set, then the display shows the initial temperature of 750C). If after 5 seconds the water temperature is not adjusted, the display will set the water heating temperature and begin heating / maintaining the set temperature.
If the water temperature is lower than the set temperature, the heater continues to operate.
If the water temperature is higher than the set one, the heater stops working and the system goes into mode maintaining the set temperature.
When the mode of maintaining the set temperature is turned on, when the temperature drops by 50C, the heater turns on.
e) Mode of maintaining the set temperature: the heater is on, press the “temperature adjustment” button, the display will show the previously set temperature, press the button to enter the operating mode, the display will light up the set value, then each press of the button the temperature value will increase by 50C . The sequence of temperature changes is as follows:
35→ 40→ 45 → 50 → 55 → 60 → 65 → 70 → 75→ 35
If you stop pressing the button within 5 seconds after stopping adjustments, the value is set and returned to the initial position.
f) When you press the “on-off” button again, the heater goes into standby mode and displays the water temperature value on the display.
2. Overheat protection:
If, while the heater is on, it stops working and goes into protection mode, then its further operation is possible only after the malfunction is eliminated.
a) insufficient water level: if during checks the temperature in the heater increases by more than 20 C in 4 seconds during 7 consecutive starts, check the water level in the heater. In this case, the “E2” mark appears on the display screen. If it appears, you must disconnect the heater from the power supply and recheck after filling.
b) temperature sensor malfunction: when the temperature sensor is short-circuited, the “E3” mark appears on the display screen.
c) malfunction of temperature readings: if during control the temperature exceeds 900 C, then the “E4” mark will appear on the display screen. Turn off the power and check. If the safety device is activated due to overheating, automatic start-up cannot be performed. Repairs must be carried out in a specialized workshop.
3. When the water pressure is less than 6 bar, the safety valve may leak. This is normal.
4. If you do not use the heater for a long time, close the cold water supply valve and disconnect the device from the electrical network.
5. Points that require attention
1. When using the heater for the first time, completely removing water from the tank and removing sediment, make sure that the device is filled with water and only then plug it into the network.
2. If the power cord is damaged, it should be replaced with a special cord or kit obtained from the manufacturer or its agent.
3. In winter and cold areas, when the heater is not used for a long time, drain the water from the heater. To do this: close the cold water supply valve, open the drain tap on the safety valve and open the hot water tap on the mixer, then drain the water.
4. Do not use plastic or aluminum hoses as supply pipes.
5. This electric water heater requires a safe and reliable grounding.
6. A safety valve must be installed on the electric heater fill tube.
7. The heater fill and drain holes cannot be closed at the same time.
8. The external cross-section of the water heater electric cable must be at least 2.5 mm2, and the protective current leakage regulator must be designed for a current strength of at least 25 A.
9. This type of electric heater is equipped with electrical cables that do not have connectors, so when connecting to power supplies, use switches that provide reliable interruption (for example, switches or circuit breakers, the interruption point distance must be at least 3 mm).
6. Service
During operation, clean the heater once every six months.
Sequence of actions: disconnect the water heater from the network, turn off the water tap, open the drain valve by turning the handle, open the drain hole (be careful not to get scalded) and drain the dirt.
If there is severe scale formation in the heating tubes or a large amount of sediment, remove the heating tubes and clean them. When reinstalling them, observe the following steps: the bolts should be tightened evenly, without significant force, and the fixing support should not be tilted. The power supply can only be connected after the product has been filled with water. If the heater is not used for a long time, turn off the cold water supply tap and disconnect the water heater from the power supply. If the water pressure exceeds 6 bar, drops of water may appear at the drain hole of the safety valve or a leak may occur.
a) A rare appearance of water drops on the drain hole of the safety valve means normal operation of the heater. To prevent water droplets from appearing on the safety valve drain hole for a longer period of time, keep the cold water inlet valve open.
b) Frequent drops of water appearing on the drain hole of the safety valve means that the water pressure is higher than normal. In this case, it is necessary to install a pressure relief valve on the cold water supply pipes, which should be located at the maximum distance from the heater.
c) To drain the resulting drops of water, a drain tube can be used, the end of which should be directed downwards and not be closed.
d) The approximate service life of the magnesium anode is 1 year, after which it is recommended to replace it by service center specialists.
7. Scope of delivery
1. Water heater – 1 pc.
2. Safety valve – 1 pc.
3. Drain hose – 1 pc.
4. Mounting kit - 1 pc.
5. Instructions – 1 pc.
The most common malfunctions and their elimination.Type of malfunction | Cause of malfunction | Debugg |
When connecting the power supply, there is no indication on the indicator screen. | Poor contact or no power supply | Connect to the power source, check the contacts |
Electrical circuit malfunction | Special type of repair |
|
The heater is not filled with water | Special type of repair |
|
Failure of internal connections | Special type of repair |
|
Special type of repair |
||
Water overheating, activation of the protective device | Special type of repair |
|
No water coming out | Incorrect connection of supply pipes | Connect correctly |
Valve clogged | Clean the valve |
|
Extended heating time | Severe scale formation | Carry out special repairs |
The heating element has failed | Carry out special repairs |
|
Regulator malfunction | Carry out special repairs |
|
Lack of water | Determine if there is a leak. |
|
Sensor failure | Carry out special repairs |
|
Overheat | Carry out special repairs |
Attention:
If such malfunctions occur as: leakage of the water heater tank, frequent operation of the protective device and other malfunctions requiring a special type of repair, disconnect the water heater from the power source, shut off the cold water supply line and notify the service department. Independent dismantling of the boiler is possible only with the consent of the local service center and the seller. Failure to comply with this requirement may void the warranty..
Life time:Established by the manufacturer, in accordance with clause 2 of Article 5 of the Federal Law of the Russian Federation “On the Protection of Consumer Rights”, the service life for storage type water heaters is 7 (seven years provided that the product is used in strict accordance with these operating instructions and relevant technical standards. Please do not confuse service life with warranty period. Using untreated water reduces the service life of water heaters. At the end of its service life, the product is considered unsuitable for use for its intended primary (or functional) purpose and must be disposed of in accordance with current legislation.
Manufacturer:
Texton Corporation LLC - Texton Corporation LLC
1201 Market Street, Wilmington 19801, Delaware, USA
The device has passed mandatory certification.
10. Warranty
This warranty is provided by the manufacturer in addition to the consumer rights established by the current legislation of the Russian Federation, and in no way limits them.
This guarantee is valid:
· on the tank water heater 5 years from the date of purchase of the product, provided that the device is used correctly*.
* proper operation means mandatory annual maintenance and replacement of the magnesium anode.
· for electrical and electronic components – 1 year.
and implies warranty service of the product in case of detection of defects related to materials and production. In this case, the consumer has the right, among other things, to have the product repaired free of charge. This warranty is valid subject to the following conditions:
The product must be purchased only in Russia, and exclusively for personal household needs. The product must be used in strict accordance with the operating instructions in compliance with the rules and safety requirements. The manufacturer's obligations under this warranty are fulfilled in Russia by sellers - authorized dealers of the manufacturer and official service centers. This warranty does not apply to products purchased from sellers not authorized by the manufacturer, who are independently responsible to the consumer in accordance with Russian legislation. This warranty does not cover product defects resulting from:
- Chemical, mechanical or other influence, ingress of foreign objects into the inside of the product; Incorrect operation, which consists of using the product for purposes other than its intended purpose, as well as installing and operating the product in violation of the rules and safety requirements; Wear of parts with a limited period of use; Wear of parts associated with violation of regular maintenance conditions; Repair of a product performed by persons or companies that are not authorized service centers*;
For all warranty issues regarding POLARIS products, please contact your nearest authorized POLARIS retailer.
