How to drill a hole in the wall with different materials of the structure

The drilling of the holes in the wall must be done both under capital construction and in everyday life. And in this matter it all depends on the material of the base plane and the diameter of the opening. Therefore, it is necessary to choose the material of the manufacture of drill. After all, there is a significant difference.

The drill to perform the hole in the brick will not withstand concrete and just burn. Today we will look at how holes are made in different materials. Also on the video in this article and the photo you can find out the tool options and choose the desired one.

Installation using the drilling of rectification in our time is quite easy. If a person is trained and correctly uses modern electrical instruments, then difficulties will not arise. To do after work, your accommodation remains clean, use the conductor, which allows you to drill, having a minimum of dirt and dust.

Make a hole in the wall is the easiest perforator, it is his advisses to apply professionals. It will best handle with the most durable materials in the wall and the best has not yet invented anything. But such an electric tool is expensive and not everyone can buy it for home use. Making holes in the wall will help the electric drill effect.

Cutting holes in the walls in most cases is precisely the drill. This tool is practically in every family, and experts give their recommendations, they will allow to expand the scope of the use of drings.

Attention: choosing a drill, carefully read the technical descriptions. The power of the electrical appliance must have no less - 600 W, and the turns may be no more than 2500 per minute and this is during the regulation mode.

So:

Required reversewhich changes the rotation of the drill clockwise and against it. Choose a model with a quick cartridge, only then you will not spend an extra time to search for a key to replace the drill.

Do not forget that the device must have a hit function. It will help to cope with any complexity of the wall surface, and drill holes will be quite easy and simple. And all, because such materials as bricks, cement or concrete are quickly destroyed from dynamic actions, namely, shocks. If the electric drill is not equipped with such a shock function, then the simplest drilling process will be delayed for a long time. The drill will be clinging for the composition located in the wall and at the same time heavily warm himself, and there will be a little sense from it. This is such a feature as shock drilling takes place in general. This is something like dulling chisel.

How to choose a suitable drill

Probably, everyone saw a huge range of different types of drills in stores and markets. Now we will deal where what is best to use. Wooden, plasterboard or foam concrete surface of the walls is not difficult to drill the most common drill.

If the material is brick, stone or concrete, then it is better to choose a drill from solid alloys. Unlike the previous one, it has a winning cutting plates. Welding elements are visible on the edge.

If your house has at least a couple of such drill with dimensions from 6 mm. Up to 8 mm is already perfect. Be sure they will also need. With their help, you can make a hole in a depth of 20 cm.

When you needed to make a large hole, then you need to buy a boring. They drill tight surfaces almost per meter deep, but only with the help of the perforator, the ordinary drill does not help here.

So:

The borants have tails with a diameter - 15 mm. And more, there are grooves that serve for fastening. But if the drill works as a perforator, then they are plugged in the cartridge. The characteristic of the bora is on the tail itself.
If you need to drill a durable surface, this process is separated into several steps, the drilling will be safe and quickly.
First choose the car long up to 20 cm. Defined for almost 15 cm.
Next use a long boring is designed for 35 cm.
Ends the drilling 50 - centimeter brown. For this you need a powerful drill, but notice earlier, we mentioned that it is not designed for heavy loads unless for individual cases.
If the punch of the perforator is not possible, take it for a minute for several hours.

ATTENTION: Punching of the holes in the wall d \u003d 150 mm and more, is best made the bromard. They are quite large in length and they have a reliable mount in the cartridge.

Safe drilling of recesses in the wall

Drill the hole in the wall is quite possible and with your own hands. But at the same time it is necessary to do everything quickly, efficiently and safely. For a different material of the wall there is also their own instructions for the rules of performance. This is read in detail below.

ATTENTION: Before starting work, carefully read the surface of the walls, make sure that there are no electrical or some other cables in places for drilling. Through the hurry and inattention damaged wires, and the worse under threat can be their own health. You ask, and how not to get into the cable? Now we'll figure it out in detail.

What to do not get into the wire

On the walls there are switches or sockets carefully inspect them. From them vertically, the network wires are diverged and go straight to the junction box.

If everything is so, it is perfect, but rarely. Usually, electricians do not always follow the rules to save the cable, it is carried out diagonally.

So:

Most often, appliances are used to check the presence of cable, they do not have the highest and definition goes fast enough.
If you do not have an instrument, then you should know that the wire is at a depth of 10 mm. To check its presence, very carefully, with what neither a stupid tool will continue the surface. If there did not find the presence of a cable, you can safely drill. Experts advise to make a deepening a little more, let it be 20 mm.
Do not press a drill to the wall and inspect every few millimeters, whether there is no wiring there. Also in specialized stores can be purchased a special device that determines where the electrical network wire is located. Be sure to take an interest on the quality and choose the best, my own health depends on its proper operation. Also, with normal and folded work, the device can be found a place where the fittings in concrete surfaces passes.
Copper electrical wiring is quick if it is recessed at a depth of 10 mm. But the aluminum cable is determined only if the device has a metal detector function. When searching constantly, look at the indicator that is equipped with a LED light bulb and also he publishes a signal, so be careful, your "helper" will give a sign.
With a metal detector mode, in the case of the location of the eclectic wire, the diode will light up and you will hear a continuous sound. In each normal device there must be a regulator for sensitivity. Food seeker depends on the battery of the crown.

ATTENTION: Not a single builder engaged in the installation of suspended and stretch structures on the ceiling surface without it. The fact is that systems are fixed with the help of self-tapping screws on the ceiling itself, and there are all electricity cables.

Drilling holes on reinforced concrete surface or brick

Now consider how to make a hole and brick in a concrete wall. Brick is easily drilled by a winning drill.

To the place where drilling will be carried out, attach the conductor and drill the slot, the turnover of the power tool must not be large, the drill should not overheat.

If the surface of the walls or ceiling is made of durable cement, then it is quite difficult to drill them. Typically, the material is selected gras 400, work on it is carried out quickly without much difficulties. It is possible if the building is still an old building, then there is a durable concrete and the drilling process will delay.

Manufacturers in the wall panels and blocks for quality are embedded in them with iron fittings - these are such twisters with a thickness of no more than 20 mm. And they can add rubble. With such a task, the drill from winning will not cope.
There is always a way out when it became clear that the drill found fittings, use the usual drill. If it is not at the right time, you can move the place to deepen up or down diagonally.
Granite crushed stone crumble in the wall from the blows of the drill, we are afraid that during such a process, the tool sometimes encourages to relieve the mechanism for four turns.
When the barrier was removed, continue to drill the surface to the winning drill. The perforator and the boring will cope with the problem of quickly and drilling holes will be much more successful.

Holes in Caffe

If you need to make a hole in the tile, use the drill that has widged protrusions and they are made by the form of teeth. This is a crown for drilling a tile.

But sometimes it is necessary to make not a large hole and the crown is not suitable. Then make a label in place.

For such a process, pick up the core if it was not found, use the usual self-tapping screw or a thick clove with a sharp tip. Carefully remove the glaze from the tile where you will drill a hole. Tool speed At the same time, set small as for a brick surface.
After when the glaze is removed, then we make a hole with a small drill.
After that, it is expanding it to the desired diameter with a twisted drill.

Gearing in the wall of large sizes

When mounting ventilation systems, you need to make a wide recess - 20 mm. Sometimes in the wall hide the meter showing electricity indicators, then at all you need to make a niche on the surface. In his own house, this is done using drill from solid alloys.

So:

Neat pencils back on the wall place for deepening. On the wall from the outside, the hole drill with a drill with a diameter is not less than 5 mm. At a distance of 15 mm.
For recess to 20 cm. It is necessary to perform almost 30 revolutions of the drill. Only then the chisel or hammer, remove the materials, while doing the niche of the desired size. If the diameter of the drill is smaller, the edges are neat, but the holes will need to make a large number for this.

It may be that option that the wall surface is solid, and to get through deepening the drilling steps are divided into several processes:

If you can drill the surface on both sides, then you first do it with one, and only then make a complete end-to-end depression. And repeat the steps done until the hole is satisfied.
When it is not possible to drill the wall surface, from one and the second sides, then do the processes in alternately a few steps. From the previously made mark, spend another line, and as soon as you chose the wrong material you can deepen a drill in a niche, not touching the edges on the wall. To facilitate the work at the very beginning, select a long drill.

Tips to help make the most accurate drilling

It turns out, there is nothing complicated in the drilling of recesses in the surface of the walls:

From the side of the conductor, we glue with a scotch or glue of the sandpaper sheet. Its size depends on the area where the hole will be. Thus, the adhesion of the device with the surface of the wall will increase and you make an accuracy of the perfect hole in the right place. It is also possible to use the stationary limiter. Its price is not large and can be purchased in retail networks.

Sometimes you need to drill a hole under the dowel, they can be different diameters, but usually it is up to 10 mm. It all depends on the fact that you will hang and its weight and, of course, from the density of the material in the wall.
For the conductor to be universal, drill in it with a regular drill a pair of holes of the desired size so that the device can be hung.
It is possible to attach a plate to the conductor, so that such a shelf protects the surface of the walls of the walls and garbage. You can use such a device when carrying out recesses for attaching plinths to the floor and wall.
Source the space on the conductor of the desired size on the selected height from the shelf, and drill the holes. In order to make the recess simply put the shelf on the floor, and all the slots will be triggered strictly in size and the desired height. Having done the installation, gradually adhering to the rules, the plinth will be tightly lying on the floor surface.
If you need to hang on a wall, some decorative element is a picture, a photo frame and much more, without having an auxiliary conductor you cannot cope. The fact is that the holes should be on a clear distance among themselves. In general, consider your own wishes and a single stylistic room.
To do it yourself, the conductor which serves for the most correct drilling of the holes, select the paneur or metal sheet. Make a marking on it and do the desired amount of rewards with a regular drill.

Let's look at the option when you need to fix parts on one screw, but on several:

The first hole is fermented on the wall, and the second is made in size equal to the size of the self-press. Use the conductor to accurately. And then a dowel is clogged into the hole.
You can fasten the conductor to the surface of the wall using a self-pressing and dowel, align it with a water level, so your drilled recesses will be smooth on one horizontal line.
Using a simple conductor, which, as you already understood, can be made personally for literally half an hour, deepening drilled drill will be accurate at the desired distance from each other.
Given this technology, you can make holes at a fairly large range. To do this, drill first holes, thus, as previously discussed, then screw the conductor on both sides by self-refuses and make the remaining deepening drills.

ATTENTION: If you think through the hole in the wall, skip the cable, then make it 20% more, because it must lie freely and not clarify.

How to drill a hole of a large diameter in the wall you now know. Do not hurry and apply the markup. Using the limiters, you will make the desired depth and diameter. The hole in the brick wall is not a complex, but requires the accuracy of the manufacture.